All NETLAB+ supported labs in the CCNA2 Routing and Switching - Routing and Switching Essentials course are supported by both the Multi-purpose Academy Pod (MAP) and Multi-purpose Academy Pod w/ASA (MAP w/ASA).
| Lab Number | Title | Pod Required |
|---|---|---|
| 1.1.4.6 | Configuring Basic Router Settings with IOS CLI | MAP or MAP w/ASA |
| 2.2.2.5 | Configuring IPv4 Static and Default Routes | MAP or MAP w/ASA |
| 2.2.4.5 | Configuring IPv6 Static and Default Routes | MAP or MAP w/ASA |
| 2.3.2.4 | Troubleshooting IPv4 and IPv6 Static Routes | MAP or MAP w/ASA |
| 3.2.1.9 | Configuring Basic RIPv2 | MAP or MAP w/ASA |
| 5.1.1.6 | Configuring Basic Switch Settings | MAP or MAP w/ASA |
| 5.2.2.9 | Configuring Switch Security Features | MAP or MAP w/ASA |
| 6.2.2.5 | Configuring VLANs and Trunking | MAP or MAP w/ASA |
| 6.2.3.9 | Troubleshooting VLAN Configurations | MAP or MAP w/ASA |
| 6.3.2.4 | Configuring Per-Interface Inter-VLAN Routing | MAP or MAP w/ASA |
| 6.3.3.7 | Configuring 802.1Q Trunk-Based Inter-VLAN Routing | MAP or MAP w/ASA |
| 7.2.2.6 | Configuring and Modifying Standard IPv4 ACLs | MAP or MAP w/ASA |
| 7.2.3.4 | Configuring and Verifying VTY Restrictions | MAP or MAP w/ASA |
| 7.3.2.5 | Troubleshooting Standard IPv4 ACL Configuration and Placement | MAP or MAP w/ASA |
| 8.1.2.4 | Configuring Basic DHCPv4 on a Router | MAP or MAP w/ASA |
| 8.1.2.5 | Configuring Basic DHCPv4 on a Switch | MAP or MAP w/ASA |
| 8.1.4.4 | Troubleshooting DHCPv4 | MAP or MAP w/ASA |
| 8.2.3.5 | Configuring Stateless and Stateful DHCPv6 | MAP or MAP w/ASA |
| 8.2.4.4 | Troubleshooting DHCPv6 | MAP or MAP w/ASA |
| 9.2.2.6 | Configuring Dynamic and Static NAT | MAP or MAP w/ASA |
| 9.2.3.7 | Configuring Port Address Translation (PAT) | MAP or MAP w/ASA |
| 9.3.1.5 | Troubleshooting NAT Configurations | MAP or MAP w/ASA |
| 10.1.2.5 | Configure CDP and LLDP | MAP or MAP w/ASA |
| 10.2.3.6 | Configuring Syslog and NTP | MAP or MAP w/ASA |
| 10.3.1.9 | Managing Router Configuration Files with Terminal Emulation Software | MAP or MAP w/ASA |
| 10.3.1.10 | Managing Device Configuration Files Using TFTP, and Flash | MAP or MAP w/ASA |
| 10.3.1.11 | Configure and Verify Password Recovery | MAP or MAP w/ASA |
| SBA | Skills-Based Assessment | MAP or MAP w/ASA |
To enable the CCNA Routing and Switching - Routing and Switching Essentials labs, create a class and check the appropriate global labs in the class settings as described in the table below, depending on the pod(s) that will be used. You may also select the Skills-Based Assessment, as indicated in the table below.
| Pods | Global Labs | Instructions |
|---|---|---|
| Multi-purpose Academy Pod | AE CCNARS RSE v6.0 - MAP - English | On the Global Labs section of the class settings, check the "AE CCNARS RSE v6.0 - MAP - English" if the MAP will be used to perform the labs. |
| Multi-purpose Academy Pod w/ASA | AE CCNARS RSE v6.0 - MAPASA - English | On the Global Labs section of the class settings, check the "AE CCNARS RSE v6.0 - MAPASA - English" if the MAP w/ASA will be used to perform the labs. |
| Multi-purpose Academy Pod | AE CCNARS RSE SBA v6.0 - MAP - EN | On the Global Labs section of the class settings, check the "AE CCNARS RSE SBA v6.0 - MAP - EN" if the MAP will be used to perform the SBA. |
| Multi-purpose Academy Pod w/ASA | AE CCNARS RSE SBA v6.0 - MAPASA - EN | On the Global Labs section of the class settings, check the "AE CCNARS RSE SBA v6.0 - MAPASA - EN" if the MAP w/ASA will be used to perform the SBA. |
The Multi-purpose Academy Pod (MAP) is also available for "pod-only" reservations. To enable pod-only reservations, select the check box for "Multi-purpose Academy Pod (no labs)" in the class settings.
The Multi-purpose Academy Pod with ASA (MAP w/ASA) is also available for "pod-only" reservations. To enable pod-only reservations, select the check box for "AE MAP w/ ASA (no labs)" in the class settings.
"Pod-only" reservations are not tied to specific lab exercises. Therefore, the pod will be configured using the default network configuration and will not be properly configured to complete CCNA Routing and Switching - Routing and Switching Essentials labs.
Always select the correct lab exercise for the lab being performed. Students or teams should schedule the correct lab exercise from the catalog. NETLAB+ will only show those labs for which the required pod type is available. A lab that works on different pod types may appear more than once if your system is so equipped. Instructors should select the correct lab from the Exercise tab during instructor-led lab reservations. This can be done as many times as needed during the reservation.
Importance of Choosing the Correct Lab Exercise
Several of the labs may differ from the standard pod topologies. This is
handled by NETLAB+ Dynamic VLAN Mapping technology. Always select the
correct lab exercise for the actual lab. This insures that NETLAB+
will set up VLANs on the control switch such that lab devices and PCs are
placed in the correct LAN segment for the exercise being performed. Selecting
the correct exercise will also make the completed lab output easier to find in
the archive.
